Assignments of Tascam FW-1884 interface elements to Logic functions are covered in the following sections.
Note: The relevant devices are highlighted in the heading of each section.
The following table outlines the encoder controls and their assignments:
Control | Assignment |
---|---|
FLIP | Switches Flip mode between Off and Swap. In Swap mode, the parameter controlled by the fader and encoder of each channel strip is swapped. |
PAN | Assigns Pan to encoders. |
AUX 1 | Assigns Send 1 level to encoders. |
AUX 2 | Assigns Send 2 level to encoders. |
AUX 3 | Assigns Send 3 level to encoders. |
AUX 4 | Assigns Send 4 level to encoders. |
AUX 5 | Assigns Send 5 level to encoders. |
AUX 6 | Assigns Send 6 level to encoders. |
AUX 7 | Assigns Send 7 level to encoders. |
AUX 8 | Assigns Send 8 level to encoders. |
The following table outlines the shortcut controls and their assignments:
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Control | Modifier | Assignment |
---|---|---|
SAVE/F1 | Saves the active project. The button LED is lit when the project has been edited since the last Save operation. | |
REVERT/F2 | Reverts to the most recently saved version of the project. | |
ALL SAFE/F3 | Disables the Record Enable buttons of all channel strips. | |
CLR SOLO/F4 | Switches Solo off for all channel strips. | |
SHIFT | Switches Mute off for all channel strips. | |
MARKERS/F5 | Creates a new marker at the current playhead position. | |
SHIFT | Deletes the marker at the playhead position. | |
LOOP/F6 | Enables/disables Cycle mode. | |
CUT | Cuts the current selection (of regions or events) and places it on the Clipboard. | |
DEL | Deletes the current selection. | |
COPY | Copies the current selection to the Clipboard. | |
PASTE | Pastes the Clipboard contents to the current playhead position. | |
ALT/CMD | Modifier for other buttons. | |
UNDO | Performs an Undo of the last editing operation. The button LED is lit when a Redo is possible. | |
SHIFT | Performs a Redo (reverses an Undo operation). | |
SHIFT | Modifier for other buttons. | |
CTRL | Modifier for other buttons. |
The following table outlines the channel strip controls and their assignments:
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Control | Modifier | Assignment |
---|---|---|
REC LEDs | These LEDs are lit when the corresponding channel strip is recording. The LEDs flash when the channel strip is in Record Enable mode (armed). | |
SEL | Selects the channel strip. | |
SHIFT | Enables/disables Send bypass, when encoders are controlling a Send level. | |
READ | Sets the track automation mode to Read. | |
WRITE | Sets the track automation mode to Write. | |
TCH | Sets the track automation mode to Touch. | |
LATCH | Sets the track automation mode to Latch. | |
SOLO | Enables/disables the Solo state of the channel strip. | |
SHIFT | Disables the Solo state for all channel strips (driver version 1.20 or later required). | |
MUTE | Enables/disables the Mute state of the channel strip. | |
SHIFT | Disables the Mute state for all channel strips (driver version 1.20 or later required). | |
Encoder | Controls the parameter chosen with the ENCODERS section. | |
SET | When encoders are controlling a Send level, this combination allows you to set the send destination. | |
Fader | Controls the channel strip volume. |
The EQ controls apply to a certain EQ band of the selected channel. A Channel or Linear Phase EQ is automatically inserted in the channel, if not already present.
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Mode | Modifier | Assignment |
---|---|---|
REC | While REC is held down, the SEL buttons activate or deactivate Record Enable for the corresponding channel strip. | |
GAIN | Edits the Gain of the currently selected EQ band. | |
SET | Selects the channel strip input. | |
FREQ | Edits the Frequency parameter of the currently selected EQ band. | |
SET | Selects the channel strip output. | |
Q | Edits the Q Factor of the currently selected EQ band. | |
SET | Selects the channel strip input format. | |
HIGH | Selects EQ band 6. | |
SHIFT | Selects EQ band 8. | |
REC | Switches the bypass state of EQ band 6 (driver version 1.20 or later required). | |
HI-MID | Selects EQ band 5. | |
SHIFT | Selects EQ band 7. | |
REC | Switches the bypass state of EQ band 5 (driver version 1.20 or later required). | |
LOW-MID | Selects EQ band 4. | |
SHIFT | Selects EQ band 2. | |
REC | Switches the bypass state of EQ band 4 (driver version 1.20 or later required). | |
LOW | Selects EQ band 3. | |
SHIFT | Selects EQ band 1. | |
REC | Switches the bypass state of EQ band 3 (driver version 1.20 or later required). |
The three buttons at the bottom of this control surface section determine the mode of other controls:
EQ/Pan mode: The controls apply to a certain EQ band of the selected channel.
AUX 1–4 mode: The controls apply to Sends 1–4.
AUX 5–8 mode: The controls apply to Sends 5–8.
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Mode | Modifier | Assignment |
---|---|---|
REC | While REC is held down, the SEL buttons activate or deactivate Record Enable for the channel strip. | |
EQ GAIN–AUX 1/5 |
| |
SET | Selects the channel strip input. | |
EQ FREQ–AUX 2/6 |
| |
SET | Selects the channel strip output. | |
EQ Q–AUX 3/7 |
| |
SET | Selects the channel strip input format. | |
PAN–AUX 4/8 |
| |
EQ HI–AUX 1/5 |
| |
SHIFT |
| |
REC | Switches bypass state of EQ band 6. | |
EQ HI MID–AUX 2/6 |
| |
SHIFT |
| |
REC | Switches bypass state of EQ band 5. | |
EQ LO MID–AUX 3/7 |
| |
SHIFT |
| |
REC | Switches bypass state of EQ band 4. | |
EQ LOW–AUX 4/8 |
| |
SHIFT |
| |
REC | Switches bypass state of EQ band 3. | |
EQ/PAN | Chooses EQ/PAN mode. | |
SHIFT | Enables/disables Flip mode. With Flip mode enabled, the faders control Pan. | |
AUX 1–4 | Chooses AUX 1–4 mode. | |
AUX 5–8 | Chooses AUX 5–8 mode. |
This fader always controls the master volume. If no master channel exists, it controls Output 1/2.
The following table outlines the automation/clock rate controls and their assignments:
Control | Assignment |
---|---|
READ | While READ is held down, SEL buttons are lit if a channel strip is in Read automation mode. Pressing the SEL button sets Read mode. Turning the encoder also edits the automation mode. |
WRITE | While WRITE is held down, SEL buttons are lit if a channel strip is in Write automation mode. Pressing the SEL button sets Write mode. Turning the encoder also edits the automation mode. |
TCH | While TCH is held down, SEL buttons are lit if a channel strip is in Touch automation mode. Pressing the SEL button sets Touch mode. Turning the encoder also edits the automation mode. |
LATCH | While LATCH is held down, SEL buttons are lit if a channel strip is in Latch automation mode. Pressing the SEL button sets Latch mode. Turning the encoder also edits the automation mode. |
F7 | Switches encoders to editing of pan/surround parameters on selected channel strip. Surround parameters are shown as follows: angle, radius, LFE (level), Spread mode, X, Y, Center (level). |
F8 | Switches encoders to Channel view: EQ Edit mode for the selected channel strip. In this mode, the encoders are used to edit the EQ parameters, while the left/right cursors are used to shift the EQ parameter bank (parameter group). |
F9 | Switches encoders to Channel view: Plug-in Edit mode for the selected channel strip. In this mode, the left/right cursors are used to shift the plug-in parameter bank. The up/down cursors are used to choose the channel strip Insert slot for editing. |
F10 | Switches encoders to Channel view: Instrument Edit mode for the selected channel strip. In this mode, the left/right cursors are used to shift the instrument parameter bank. |
The following table outlines the mode controls and their assignments:
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Control | Modifier | Assignment |
---|---|---|
F1 | Saves the active project. The button LED is lit if the project has been edited since the last Save operation. | |
SHIFT | Opens the Save As dialog. | |
F2 | Performs an Undo of the last editing operation. The button LED is lit when a Redo is possible. | |
SHIFT | Performs a Redo. | |
F3 | Copies the current selection (of regions or events) to the Clipboard. | |
SHIFT | Cuts the current selection and places it on the Clipboard. | |
F4 | Pastes the Clipboard contents. | |
SHIFT | Clears the current selection. |
The following table outlines the master controls and their assignments:
Note: If a modifier button, such as SHIFT, is shown below a button description, it indicates that the control has an alternate use while the modifier is held down.
Control | Modifier | Assignment |
---|---|---|
Cursor buttons | Identical to (but independent of) the computer keyboard arrow keys, except when encoders are in EQ, Plug-in, or Instrument Edit mode. | |
SHIFT | Horizontally or vertically zoom in and out (of the window with key focus). | |
SHTL | Enables Shuttle mode for the wheel. | |
Wheel | Shuttle mode off: moves playhead by one bar. Shuttle mode on: shuttles playhead. | |
Bank LEDs | Shows currently selected fader bank. If you only have an FW-1884, a bank refers to eight channels. If you have FE-8 extensions added, a bank encompasses the total number of (physical) channel strips: 16, 24, and so on. If no LED is lit, bank 5 or higher is selected. | |
< BANK | Shifts fader bank down by one bank. | |
SHIFT | Shifts fader bank down by one channel. | |
SET | Switches to Mixer (multichannel) view (driver version 1.20 or later required). | |
BANK > | Shifts fader bank up by one bank. | |
SHIFT | Shifts fader bank up by one channel. | |
SET | Switches to Mixer view and shows all Aux and Output channels (driver version 1.20 or later required). | |
<< LOCATE | Goes to previous marker. | |
SET | Deletes the current marker (driver version 1.20 or later required). | |
LOCATE >> | Goes to next marker. | |
SET | Creates a new marker at the playhead position (driver version 1.20 or later required). | |
NUDGE buttons | Nudges the selected event/region left or right (by the current nudge value). | |
SET | Chooses the current nudge value: tick, division, denominator, bar, frame, 1/2 frame. | |
SET | Modifier for other buttons. | |
IN | Moves playhead to left locator position. | |
SET | Sets left locator at current playhead position. | |
SHIFT | Sets punch in locator at current playhead position. | |
OUT | Moves playhead to right locator position. | |
SET | Sets right locator at current playhead position. | |
SHIFT | Sets punch out locator at current playhead position. | |
REW | As per Rewind key command. | |
FFWD | As per Forward key command. | |
STOP | Stops playback. | |
PLAY | Starts playback. | |
REC | As per Record key command. |